Harmony Epoxy Primer is a two-component liquid epoxy adhesive, activated by mixing.
It is designed for application as a primer on wet base surfaces, such as showers, sinks, washbasins or, more generally, any base surface which is in regular contact with water or humidity, prior to the application of Harmony Waxed Concrete.
Harmony Epoxy Primer must be applied as a primer to tiling or any type of screed, including anhydrite screed, prior to the application of Harmony Smooth Concrete.
Over conventional acrylic primers Harmony Epoxy Primer has the advantage that it prevents rising damp, increases the grip and reduces the risk of blistering.
Type: Two-component resin
Density: A + B: 1,06 ± 0,02
Dry extract: 100%
Flash point: > 100 °C
Packaging: 1kg, 5kg, 25kg
Total weight of 25 kg-Sets: component A: 9 kg, component B: 16 kg,
Total weight of 5 kg-Sets: component A: 1,5 kg, component B: 3,5 kg,
Total weight of 1 kg-Sets: component A: 0.3 kg, component B: 0,7 kg
Drying time: 30 minutes to 2 hours, depending on the type of substrate and the ambient temperature.
Recoatable: At least 24 hours after application.
Storage: 6 months in unopened original packaging, stored in a dry and frost-free location.
Guarantee: Manufacturer’s liability
Mixer, roller, protective gloves.
Clean tools with acetone after use.
The base surface must be resistant, sound, solid, clean, dry and free of humidity.
Use Harmony neutral agent or Harmony degreaser for any cleaning required (to remove grease, oil, etc.).
On new flooring and/or in building which has yet to be occupied, a minimum waiting time of 36 hours is advised, subject to compliance with the drying time for the foundation slab.
Open the crack with the help of a diamond grinding wheel. Extract dirt particles with a blower or air compressor. First fill the gap with the epoxy resin primer (make sure that component A and component B are well mixed) and then apply the same mixture with the roller over the surface again.
Let it dry for 48 hours.
The ambient temperature, and the temperature of the base surface, must lie within
a range of + 5° to + 30 °.
The mix will remain workable for 15 minutes. It is advised that two people should be available to apply the mix.
If this is not possible, and depending upon the area to be covered, divide component A and component B into a number of batches, then mix progressively as work proceeds.
Example: in the case of a 5 kg kit, divide component A into two batches and component B into two batches.
Pour component B of Harmony Epoxy Primer into component A and mix using a stirrer operating at low speed to form a uniform paste.
Apply Harmony Epoxy Primer to the surface immediately using a roller. For large surface areas, use the 250 or 500 mm PermaPro special floor nozzle.
Screen by the progressive application of Harmony Sand as the application of Harmony Epoxy Primer proceeds, at a ratio of 25 kg of sand per 10 m2.
In case of application to a base surface which is in regular contact with water or humidity (shower, washbasin, etc.), Harmony Epoxy Primer should be applied to the surface by roller, prior to the application of Harmony Waxed Concrete.
Allow to dry partially, then apply Harmony Waxed Concrete to the still slightly damp surface.
Allow to dry for a minimum of 24 hours before removing the surplus sand.
After vacuuming the sand, it sometimes happens that the sand does not stick in some places. This phenomenon is due to a lack of epoxy resin during application. Mostly this does not cause any problems as long as these gaps are small / do not exceed the palm of the hand. If there are large areas, you can re-apply epoxy at these locations.
|Consumption||1kg for 5m2|
|Conservation||6 months in its original packaging, unopened and stored in a dry and frost-free|
We guarantee a secure payment by
Cédric L. published the 27/12/2018 following an order made on 19/12/2018
super colle. ne pas oublier de porter des gants
Stéphane G. published the 14/11/2018 following an order made on 18/10/2018
Anonymous A. published the 27/03/2018 following an order made on 22/03/2018
Anonymous A. published the 27/03/2018 following an order made on 21/03/2018
Anonymous A. published the 01/03/2018 following an order made on 19/02/2018
produit qui colle !! rien à redire sauf attention car les outils utilisés sont morts après
Anonymous A. published the 20/02/2018 following an order made on 14/02/2018
super colle. utilisé pour faire l'accroche de mon ragréage
Anonymous A. published the 29/01/2018 following an order made on 25/01/2018
parfait mais attention colle extremement donc tout ce qui est en contact avec collera. le rouleau ne peut etre nettoyé par la suite
Anonymous A. published the 10/01/2018 following an order made on 09/01/2018
je l'ai utilisé pour parfaire l'étanchéité de ma douche car j'avais des doutes. facile d'application mais les outils ne peuvent pas être nettoyé après.
Anonymous A. published the 23/10/2017 following an order made on 16/10/2017
super colle. attention colle tout et le nettoyage des outils est impossible après
Anonymous A. published the 19/04/2016 following an order made on 08/04/2016
Tips, product information, personalized quotes?